Michigan Injection Molding Machine

5 EOAT Design Houses in Michigan .

The importance of automation and robots in all manufacturing industries is growing. Industrial robots have replaced human beings in a wide variety of industries. Robots outperform humans in jobs that require precision, speed, endurance, and reliability. Robots safely perform dirty and dangerous jobs.

When it comes to design your robotic arm, we are located in Michigan and we can design your Molding Machine.

Traditional manufacturing robotic applications include material handling (pick and place), assembling, painting, welding, packaging, palletizing, product inspection and testing. Industrial robots are used in a diverse range of industries including automotive, electronics, medical, food production, biotech, pharmaceutical, and machinery.

EOAT or End of Arm Tooling is an essential part of the process. You need a specialist for every job, and you can think about your tool as this person.

Plastic Injection Machine

This job is among one of my favorites. It’s because the entire project was mine. I started by going out to their facility and seeing their inefficiencies. One cell that they were very excited to revamp was their Silica dump cell. I was able to come up with the initial concept, quote the project for materials and labor, and then do the engineering myself. I did, not only the mechanical design and detailing, but also the electrical and pneumatic schematics. I felt in charge of the whole thing- high risk, but high reward.

A HUGE 6 axis robot (ok, not that huge, I’ve used bigger) but an R2000 robot picks up these paper bags filled with Silica. The end-of-arm-tooling (EOAT) used vacuum suction to hold onto the bag.

Solidworks Rendering of EOAT

It bring it over to a hopper, where a smaller robot uses a knife to cut the bags. The larger robot then flips it’s tooling to dump the Silica into a hopper. Seems pretty simple and for the most part it was. However, the Silica is so densely packed into the bags that even when the bags were cut wide open, the Silica wouldn’t dump. To help the Silica loosen and fall, we stick needles into the bag and blow air through these probes which moves the Silica powder around. We then (for a lack of engineering terms) flap the bag to further empty the Silica. It may sound tedious, but any powder or residue left in the bag is money wasted for the company.

An SMC slide cylinder pushed the air probes through the paper bag, and the fittings attached to the other side provided air to go through to the holes in the probe.

Another part of the project was to add a tool changer to the smaller robot. It was originally just equipped with the knife, but by adding a tool changer with a “Silica break tool” the robot was able to then go into the hopper and break up large clumps of Silica helping the contents of the hopper drain. Imagine a giant potato smasher. (Which is in fact what we ended up often calling the tool.)

Potato Smasher Robot

I had a lot of fun working with my machinist and builder on this project. I did everything I could to help them succeed, but also knew they had my back on this as well. I understand that that dynamic not all that common in the work place, so I really appreciated it. The install is happening currently and now the programmer is up to bat. The EOAT has a camera and laser to locate the bag. The camera locates the XY location of the bag and the laser the Z (height) location. I can’t wait for the tooling to be fully power, programmed, and running. I really think the customer will be happy with this addition.

Automation and Industrial Robots

?

Vacuum pumps, which are the order of the day for household and industrial uses, often need repair. Dealers of vacuum pumps offer repair and maintenance at the time of purchase, as part of warranty or otherwise. Repair work is frequently undertaken by the manufacturers of particular brands, who often know the gadgets better. Otherwise, repair kits are available, with which an individual pump owner can repair the pump him- or herself.

Repair kits are available from numerous manufacturers and are an important part for users of vacuum pumps. If one volunteers to go through the "do-it-yourself" path before undertaking repairs, the pump should be sent to a detoxification center, if toxic substances were used in the pump earlier. Workspace, lots of emery paper, sealants, cleaning solvent, new oil, and facilities for disposal of the used oil are essential aspects. A manufacturer's pump repair kit can cost about $400, and some brands cost up to $900. The kit contains a bag of gaskets, shaft seals, and ""O"" rings. Other items that will be needed include a pump repair stand, hammer, cigarette paper, and most likely a puller to remove the drive pulley.

Incidentally, it was found that air consumption could be reduced by 98 percent when a robot's end-of-arm tool was equipped with particular technologies, entailing less repair and maintenance. Automotive manufacturers have found the system integration and the implementation of standard autoracking solutions to be extremely cost-effective and adaptable when working with different robot platforms.

Injection Moulding Machine Price

Allen Park Moulding Company

How to Find a Vacuum Cup in Allen Park ?

Whether the fabricator’s shop is large or small, the Ironworker is the backbone. The Ironworker isn’t a single machine; it is five machines united into an engineering wonder. It has much more versatility than most people would imagine. The five working sections that are involved in the make-up of this machine are a punch, a section shear, a bar shear, a plate shear, and a coper-notcher.

A number of the cheaper ironworkers are constructed to employ a fulcrum where the ram shakes back and forth, making the punch go into the die at a small angle. This normally leads to the eroding of the punch and succumb on the front rims. The higher quality machines integrate a ram which moves in a direct vertical line and employs modifiable gibs and guides to assure a constant traveling path.

Injection Molding Materials

When you look for a End of Arm Tooling (EOAT)  that develop a Vacuum Cup in Allen Park, looks for experience and not only pricing.

That dedicates more life to the tooling, and allows the punch to penetrate the succumb right in the middle in order to capitalize on the machine’s total tonnage.

When looking for a design house that designs a Vacuum Cup in Allen Park  don’t look just in Michigan , other States also have great providers.

Injection Moulding Manufacturers

Industrial Robot Automation

?

Crypto Briefing

Story after story of top talent in Financial firms and Wall Street pivoting to start their own crypto and blockchain startups. The most recent is J.P. Morgan’s former head of blockchain, Amber Baldet, who has announced a new blockchain start-up called Clovyr.

Or there is this guy, who claims Bitcoin could reach as high as $50,000 by the end of 2018.

Regarding the advent of blockchain there’s a nice video here by Fortune. Amber, who most recently served as the bank’s blockchain program lead at JP Morgna Chase, is co-founding a new startup, Clovyr, that aims to help consumers, developers, and businesses explore the nascent, albeit burgeoning, world of blockchain-based, decentralized technologies.

Baldet hopes she can:

Help people think differently about decentralized application design.
  • Baldet’s post-J.P. Morgan plans have been the topic of speculation since she announced her departure from the bank in April. This is part of a growing trend, the writing is on the wall for Wall Street firms that do not remain agile, and now is the right time to pivot to the blockchain and crypto that are still somewhat nascent and could eventually disrupt financial markets and how financial services work on very fundamental levels.
Shaun Mader | FilmMagic | Getty Images

Amber won’t be the first or the last to leave the comfort of Wall Street, let’s remember where Jeff Bezos got his mathematical and strategic roots.

Baldet unveiled a Clovyr demo at the Consensus conference in Manhattan on Monday afternoon, May 14th, 2018. They are fundraising now as well.

Will Clovyr be the Apple Store for Decentralized Apps?

Baldet co-founded Clovyr with Patrick Nielsen, who led development for J.P. Morgan’s open source blockchain projects.The new company will offer something similar to an app store, but for “decentralized applications” which exist on a blockchain, points out CNBC.

Build it and they will come, we know that the blockchain is coming, even Amazon announced another major partner in its efforts on the cloud. We already knew this but Amazon’s cloud computing arm is now teaming up with startup Kaleido to help simplify blockchain technology for its clients.

Clovyr feels very much like a B2B platform dApp ecosystem in the making:

Clovyr is a decentralized application store that will host a selection of well-vetted applications alongside some in-house developer tooling designed to simplify application development for enterprises.

Seriously though, who would not want to invest in something like this?

Fortune Video

Anticipating the future is not very hard if you are a blockchain enthusiast. She is joined by Nielsen (above), former lead developer of Quorum, a JPMorgan Chase-built blockchain for business, who will serve as the concern’s chief technologist. If JP Morgan Chase is not even able to retain it’s top blockchain people, something is seriously wrong with their R&D model.

Or hang on a second, is this a spin-off play by JP Morgan itself? The report goes on to say: maintaining a “blockchain agnostic” approach to application design, Clovyr will initially provide tooling to build on both public and enterprise versions of ethereum, specifically the Quorum. These Wall Street firms know that they have to appear independent with their innovation startups to gain trust of Millennials. Someone that calls Bitcoin idiotic is probably not on the inside track of trust to the crypto hoard.

What Clovyr reminds me of is essentially a “Shopify of Crypto”, as the cofounders envision the platform serving as a neutral ground, offering a browser-like dashboard for the blockchain-curious, through which Clovyr can provide support and other services to customers according to their needs.

Does the concept make any sense to you?

Injection Molding Cost

The importance of automation and robots in all manufacturing industries is growing. Industrial robots have replaced human beings in a wide variety of industries. Robots out perform humans in jobs that require precision, speed, endurance and reliability. Robots safely perform dirty and dangerous jobs. Traditional manufacturing robotic applications include material handling (pick and place), assembling, painting, welding, packaging, palletizing, product inspection and testing. Industrial robots are used in a diverse range of industries including automotive, electronics, medical, food production, biotech, pharmaceutical and machinery.

The ISO definition of a manipulating industrial robot is "an automatically controlled, reprogrammable, multipurpose manipulator". According to the definition it can be fixed in place or mobile for use in industrial automation applications. These industrial robots are programmable in three or more axes. They are multi-functional pieces of equipment that can be custom-built and programmed to perform a variety of operations.

Industrial robots fill the need for greater precision, reliability, flexibility and production output in the increasingly competitive and complex manufacturing industry environment.

Robot End Effector Gripper

You Can Find a EOAT in Allen Park here:

 



Check the Weather in Allen Park, Michigan

Arnold Vacuum Cup

How to Find a Industrial Robots in Arnold ?

Whether the fabricator’s store is large or small, the Ironworker is the backbone. The Ironworker isn’t a single machine; it is five machines united into an engineering wonder. It has much more versatility than most people would imagine. The five working sections that are involved in the make-up of this machine are a punch, a section shear, a bar shear, a plate shear, and a coper-notcher.

A number of the cheaper ironworkers are constructed to employ a fulcrum where the ram shakes back and forth, constructing the punch go into the die at a small angle. This normally leads to the erosion of the punch and die on the front rims. The higher quality machines integrate a ram which moves in a direct vertical line and employs modifiable gibs and guidebooks to ensure a constant traveling route.

Pneumatic Gripper

When you look for a End of Arm Tooling (EOAT)  that develop a Industrial Robots in Arnold, looks for experience and not only pricing.

That devotes more life to the tooling, and allows the punch to penetrate the succumb right in the middle in order to capitalize on the machine’s total tonnage.

When looking for a design house that designs a Industrial Robots in Arnold  don’t look just in Michigan , other States also have great providers.

Injection Molding Press

Major Parts Of An Excavator And How It Works

?

By Rod Vagg

ARM: A Quick Primer

ARM is a tricky beast to describe because it’s more than one thing. In common parlance, we use it to describe a CPU architecture, akin to x86 from Intel and AMD. The ARM name comes from its designer, ARM Holdings, but they don’t actually make the hardware, unlike Intel and AMD. ARM is primarily an intellectual property company which licenses their technology to manufacturers to form a vibrant ecosystem of processor and SoC (System on a Chip) products.

An ecosystem of manufacturers

Companies such as Samsung, Qualcomm, Broadcom and even AMD (traditionally known for their x86 products) license core CPU designs from ARM, largely made up of the “Cortex” range. A number of CPU design licensees release Cortex-based processors under their own branding, which is where you see familiar names such as the Qualcomm Snapdragon, the Samsung Exynos or Nvidia Tegra.

In addition, ARM offers an architectural license that gives licensees permission to design their own CPUs that fully comply with the ARM architecture to ensure instruction set architecture (ISA) compatibility. Companies such as Applied Micro and Cavium currently hold architectural licenses and are producing their own processor designs. Apple uses an architectural license to produce its Ax series of processors, including the A7 and A8 which power the current iPhone and iPad range.

The ARM architecture

Due to the compact nature of the ARM architecture, it has traditionally been used for small devices. ARM processor designs tend to focus on efficiency as their current primary uses are in devices where power draw is a major concern. Most smartphones and tablets in the market today are based around ARM processors and they are even showing up in laptops, with many of the current Chromebook range using ARM processors.

ARM’s architecture designs are broken up in to generational versions. The most common ARM architecture generation used in smartphones, tablets and other small computers today is ARMv7. For instance, the newest incarnation of the Raspberry Pi uses an ARMv7 processor, while the original Pi used an ARMv6 processor, the previous generation.

There’s a new generation that’s starting to roll out, ARMv8 and this represents a major shift in architecture design and also a shift in the commercial potential that ARM Holdings sees for its processors.

The HiKey development board from 96Boards using an HiSilicon Kirin 6220 eight-core ARMv8 Cortex-A53 CPU

Until now, ARM’s range of processors and architecture designs have been 32-bit, meaning they have limitations in their ability to scale to uses beyond small devices. But even our smartphones are starting to push up against the barriers that 32-bit processors present, most notably the limitations to the amount of RAM you can couple with the processor. ARMv8 is a new 64-bit design that alleviates the barriers presented by 32-bits. The ARM family of processors already reaches deep into the low-power and small-size end of the market (as demonstrated b the Cortex-M0+ pictured above), but with ARMv8, there is a new target: the server market.

ARM on the Server

The phenomenal success of the Raspberry Pi saw the dawn of a whole new class of computers gaining wide acceptance: “single-board computers”. There is now a huge range of products in this market, all vying for the attention of hobbyists and commercial users alike. Even Intel is in on the game with their low-power x86 incarnation, the Atom. The low cost and surprising versatility of these small computers have lead to some interesting new uses. DataStax likes to show off their 32-node Rasperry Pi Cassandra Cluster as a way to demonstrate the versatility of Cassandra but even more, it shows the potential uses that low-cost single-board computers can be put to. Online Labs have rolled out a new IaaS (Infrastructure as a Service) product named Scaleway based completely around ARMv7 servers and are finding strong interest from customers wanting smaller and simpler cloud infrastructure.

The DataStax demonstration 32-node Rasperry Pi Cassandra Cluster

miniNodes, another IaaS company, has jumped straight to ARMv8 in its offering by using early development ARMv8 boards. The University of Utah, in its contribution to the scientific computing cloud research project CloudLab, are rolling out a cluster of 315 HP Moonshot m400 cartridges, with which HP are claiming the title of “The World’s First Enterprise-ready 64-bit ARM Server”.

Also getting in on the ARMv8 hardware action is Gigabyte, Lenovo, Hyve Solutions, SoftIron, StackVelocity and E4 who specifically target HPC applications. As 2015 rolls on, expect a flourish of new hardware to appear, pushing us to rethink some traditional approaches.

The HP Moonshot m400 ARMv8 cartridge

The new ARMv8 processors are intended to further bridge the gap between traditional ARM uses and the new forms of server computers that there is an obvious demand for. Their low-power profile will mean that their natural target will still be smaller servers but we will likely see many cluster-style products come on to the market where many ARMv8 boards are combined into a unified cluster.

The Software Stack

Just as we are seeing shifts in the hardware market, with new demand for clusters of smaller servers rather than simply continuing to push at Moore’s Law to make servers ever-bigger, we are also seeing shifts in the traditional trajectory of the software stack. Monolithic applications are now viewed as both business and technical risks. SOA (Service Oriented Architecture) is the new best-practice with experimentation all the way down to micro-services. We’re in the midst of a great ‘unbundling’ in the software world.

While the JVM is right at the heart of the monolithic software stack and the tooling that surrounds it, Node, or server-side JavaScript, is arguably at the heart of the new SOA stack. Node’s small and nimble runtime profile along with its overriding culture of modularity make it a perfect fit for a transition to the composition of applications from smaller, focused, services.

There is an interesting intersection between the changes in the hardware market and the changes in best-practice software development. Smaller, more nimble software is perfectly suited to smaller, more nimble and low-power hardware. What’s more, Node’s development model encourages developers to think multi-process from the beginning because we know that without the crutch of threads, the only way we can scale our applications is to multiply the number of processes (have you ever noticed how you rarely hear Node developers talk about “sticky-sessions” while Java developers obsess about them?). This means that Node applications scale as easily across clusters of servers as they do within a single server. Not only does the Node development model buy you free scalability, it also buys you resilience by fitting better on larger numbers of smaller servers instead of smaller numbers of larger servers as you typically see in the JVM world (although, the typical Node application performance profile means that you need significantly less total hardware investment as well).

One of the common patterns that NodeSource encounters across the enterprise as companies start waking up to the potential that Node offers them is that they need to start rethinking their hardware needs. Typically, large companies will have a homogeneous production environment, with one or two types of server available for deploying applications. Commonly these are tuned to the needs of the JVM and other monolithic application stacks so there is a priority placed the on speed and size of each hardware unit. An average server might have 16 cores and 32G of RAM and be a perfect match for a JVM application that makes liberal use of threads and is a natural memory hog. Unfortunately, this doesn’t translate very well to Node, particularly on the memory side. So we see a lot of wasted hardware in these environments with architects exploring new ways to make use of all of the free RAM they now have available. This is not ideal from a cost perspective but understandable where Node is only at the beginning of its journey into these environments.

Node and ARM: A Perfect Match

As argued above, Node is a great fit for the changes occurring in the hardware stack:

  1. Node isn’t a resource hog, it’s at home in smaller environments with its low memory profile and single-threaded nature.
  2. Node is nimble; for example, we advise our clients to kill & quickly restart when their applications enter an unexpected-error state. You can’t do this with a runtime that takes minutes to properly start and warm-up.
  3. Node’s development model and culture is naturally SOA; if you’re building a large application and it’s not made up of small services then you’re doing Node wrong. Node applications are generally scalable by default.

Another important factor here is Node’s use of V8 as a JavaScript foundation. From its early days, the Chromium project has treated the ARM platform as one of its primary targets. Chrome is on every new Android-based phone and tablet and is obviously a foundational component of Chromebooks. V8 is already heavily optimized for ARM and is moving in lock-step with ARM because it’s in the interests of both ARM and Google to do so.

io.js, the community fork of Node.js, released its 1.0 earlier this year. ARM has been second-class for Node.js until now so we encouraged a new focus on ARM as a first-class platform target for the io.js project. ARM hardware has been a fixture in the io.js CI system from the beginning and the project has been shipping ARM binaries since 1.0. Today you can download both ARMv6 and ARMv7 optimized binaries for io.js releases and nightlies right from the downloads directory. Through this focus, io.js has even been able to feed patches back in V8 to fix and improve support for ARM.

Because io.js is using current V8 releases and we have made it clear that ARM as a platform with primary support, ARM Holdings has taken an interest in the project. It’s clear that they see similar synergies to us between Node and ARM hardware, particularly with their new focus on server use of their architecture. ARM has stated publicly that their goal is to carve out 20% of the server market with its new architecture within five years, up from less than 1% today.

ARMv6 and ARMv7 boards serving in the current io.js ARM test and build cluster

We have been working with ARM to get access to test hardware for the io.js CI system to bring the codebase up to scratch on the new ARMv8 architecture. The not-for-profit Linaro organization was set up by ARM and its partners to work on bringing better ARMv7 and ARMv8 support to open source software. The organization maintains a server cluster which the io.js project currently has access to for ARMv8 test hardware and has used this resource to understand and solve the technical hurdles involved. io.js is now shipping experimental 64-bit ARMv8 binaries in its nightly distribution channel. By the time single-board ARMv8 computers are available on the general market there will also be release builds of io.js available for use. Keep an eye on 96Boards, a project by Linaro, if you are interested in affordable ARMv8 hardware.

Getting Real

Of course, any embrace of the combination of smaller servers and Node for the enterprise is likely to be part of a longer, multi-year strategy. As of right now, Node adoption is still in the early stages at most companies that are choosing to embrace it. Their immediate concerns are more about the basic architecture questions relating to unbundling monolithic structures. As new SOA models emerge, questions about the optimization of hardware platforms will arise and it’s likely that ARM will be in serious consideration.

Aside from enterprise concerns, it’s clear that ARM at least has a future in new-style, low-cost cloud platforms that may be very attractive to start-ups and those of us who are looking for cheap hosting for our side-projects.

Node is still young, and adapting to a changing hardware landscape should be easy. Through io.js, Node’s future on ARM hardware is looking very positive. NodeSource will be keenly watching how the community and companies, both small and large, react to the new possibilities as they emerge.

Injection Moulding Manufacturers

The importance of automation and robots in all manufacturing industries is growing. Industrial robots have replaced human beings in a wide variety of industries. Robots out perform humans in jobs that require precision, speed, endurance and reliability. Robots safely perform dirty and dangerous jobs. Traditional manufacturing robotic applications include material handling (pick and place), assembling, painting, welding, packaging, palletizing, product inspection and testing. Industrial robots are used in a diverse range of industries including automotive, electronics, medical, food production, biotech, pharmaceutical and machinery.

The ISO definition of a manipulating industrial robot is "an automatically controlled, reprogrammable, multipurpose manipulator". According to the definition it can be fixed in place or mobile for use in industrial automation applications. These industrial robots are programmable in three or more axes. They are multi-functional pieces of equipment that can be custom-built and programmed to perform a variety of operations.

Industrial robots fill the need for greater precision, reliability, flexibility and production output in the increasingly competitive and complex manufacturing industry environment.

Injection Molding Cost

You Can Find a EOAT in Arnold here:

 



Check the Weather in Arnold, Michigan

Baldwin Injection Molding Machine

How to Find a Vacuum Cup in Baldwin ?

Whether the fabricator’s store is large or small, the Ironworker is the backbone. The Ironworker isn’t a single machine; it is five machines united into an engineering wonder. It has much more versatility than most people would imagine. The five working sections that are involved in the make-up of this machine are a punch, a section shear, a bar shear, a plate shear, and a coper-notcher.

A number of the cheaper ironworkers are constructed to employ a fulcrum where the ram shakes back and forth, building the punch go into the die at a small angle. This normally leads to the eroding of the punch and succumb on the front rims. The higher quality machines incorporate a ram which moves in a direct vertical line and utilizes modifiable gibs and guides to guarantee a constant traveling path.

End Effector Design

When you look for a End of Arm Tooling (EOAT)  that develop a Vacuum Cup in Baldwin, looks for experience and not only pricing.

That gives more life to the tooling, and allows the punch to penetrate the die right in the middle in order to capitalize on the machine’s total tonnage.

When looking for a design house that designs a Vacuum Cup in Baldwin  don’t look just in Michigan , other States also have great providers.

Injection Molding Materials

Major Parts Of An Excavator And How It Works

?

Blacksmith Power Hammers or Trip Hammers

If you have ever worked with a power hammer you see the blacksmithing world through different eyes. Power hammers really fall into 3 basic categories, Hydraulic Presses, Mechanical Hammers, and Air Hammers. They are all designed to increase the amount of force that you can apply to the steel. This means you can do more work in a given amount of time and you can work bigger bar. Suddenly this opens a whole new creative reality with the steel.

Hydraulic Presses

I don't use one in my shop but I have used one years back in another smiths shop. Hydraulics have tons of power (literally) and can force the metal into many different shapes very effectively. They are useful for extreme controlled force applications such as forcing steel into preshaped dies, or cutting at specific lengths or angles etc.

This is not an impact machine such as mechanical hammers or air hammers, and is not fast. It can be used for drawing out steel but this is tedious. Although it would save time from drawing out by hand and allow you to work bigger bar I would go crazy with the slow process.

Essentially the machine is a hydraulic ram mounted on a frame with an electric pump. You use a foot control to squish the metal. Step with the foot apply more force. Release the foot the dies back off then you can move the bar and apply the force again in a different spot.

There are a couple of positive aspects of a hydraulic press. They have a small footprint, and require no special foundation. Prices are manageable for this type of tool. About $2000.00 in my area. There is no impact noise or vibration with this type of machine. The whine of the hydraulic pump can be loud but it doesn't have the same annoyance factor for neighbors as the impact from a hammer. Presses are rated by the number of tons pressure that the ram can produce. 20 ton, 40 ton and 60 ton are common sizes.

Most smaller blacksmithing shops use 50 lb to 150 lb size. There are two subclasses of air hammers that you should be aware of. The self contained and the air compressor version. The self contained uses two air cylinders. One is the compressor cylinder and is driven by a motor. This cylinder provides air to the hammer head cylinder. So every up stroke of the drive cylinder forces the hammer head cylinder down and every down stroke forces the hammer head cylinder up. Valving causes the air to be either exhausted or sent in varying amounts to the hammer head cylinder. This provides the control on the stroke and  force applied to the steel. This cyclic timing is governed by the speed of the electric motor.

The air compressor reliant air hammer feeds off a constant line pressure and has a feed back circuit built into the design. The hammer head travels up and trips a switch that tells it to go back down. Once it reaches a certain travel point another switch tells it to go back up. The amount of the exhaust dictates both the speed and the force applied to the steel.

Although air hammers appear to be a bit more complicated than a mechanical hammer there are actually less moving parts and less to wear out. I find them to be more versatile. You can adjust your stroke and force just by moderating your foot peddle. With a mechanical hammer you have to make a mechanical adjustment to change your stroke height. Your force is controlled by the speed of the impact or the speed of rotation.

Plastic Injection Machine

Emotional Freedom Technique or EFT is a form of psychological acupressure which uses tapping of the fingertips on specific areas of the body to relieve the emotional trauma of past events, addictions, pain, etc - as well, EFT is used as a powerful addition to positive affirmations. Learning EFT takes less than a minute and its contribution to mental health and happiness is nothing less than astonishing. You need not take anyone's word for it. In minutes you can learn and see for yourself if EFT really works. If you love yourself, or want to, EFT is for you!

Authors note: The main, companion article to "Emotional Freedom Technique - A core tool in Rapid Enlightenment," is "Rapid Enlightenment - A rapid guide to lifelong happiness" which is the core article introducing the simple and powerful, three step process of Rapid Enlightenment (To Recognize, Remove, and Relearn) your way to lifelong happiness. EFT is just one of the three essential components to the practice of Rapid Enlightenment.

There are many online examples of techniques and uses for EFT and further exploration is highly recommended. Included below is a simple introduction and hypothetical example of EFT in action. From this example you can use your own mind and creativity to substitute any negative feeling, memory, belief or situation that has been interfering with your happiness. So here we go...

Janet is afraid of dogs and has been since the day she was badly bitten by a neighborhood dog when she was seven. Since that day this long standing memory has caused many panic attacks when she is around, or even thinks about dogs. She often goes blocks out of her way to avoid dogs and social situations where dogs might be present. She has behaved like this for the last twenty-five years.

Janet will use EFT on the long standing memory of being bitten by the neighbor's dog. The idea is to attack the source of the suffering, in this case, the initial traumatizing event. By doing so, all of the emotions that sprang from this past event will also be affected - similar to destroying a tree by cutting out the root, rather than cutting off the tree's branches.

Using all of the senses of her mind, Janet recalls the traumatizing event. In her mind she becomes that little girl - seeing and feeling everything that little girl felt. Instantly she becomes ill at ease. She takes an emotional severity rating of the memory, of how much the memory makes her suffer. She rates it a ten. The most severe it could be. Nevertheless, she is in a safe place and knows she is only recalling the memory and it is not actually happening.

With the memory in full bloom, she begins tapping with her fingertips on the specific nerve centers listed below. The following is an example order of tapping but it can be in any order that feels most comfortable.

TAP ON ALL OF THESE KEY NERVE CENTERS (FINGER TAP THREE OR FOUR TIMES ON EACH NERVE CENTER BEFORE MOVING TO THE NEXT NERVE CENTRE):

How would you be without your fears? Without those emotions that feel so real but serve only to leave you in the many states of suffering? Eliminate suffering and fear and you eliminate the corrupted thinking that is blocking your happiness.

SOME IMPORTANT CLARIFICATIONS WHEN PRACTICING EMOTIONAL FREEDOM TECHNIQUE

There are two important clarifications regarding tapping. The first is to always remain attentive (self-aware) to tapping only negative feelings, memories, beliefs or situations. The mind has a habit of jumping from thought to thought quickly. Often our minds can jump from a negative state of suffering to a positive state of happiness without warning. When you observe this happening, stop tapping immediately! Take a few calming breaths and generally distract yourself before proceeding. For obvious reasons you do not want to tap towards the diminishing or removal of positive, emotional states.

Positive feelings, memories, beliefs or situations are those emotions that you know do not cause yourself or others to suffer. Every other kind of emotion can be considered, "ready to go!"

The second important clarification is to again remain attentive (self-aware) and to recognize the difference between a reasonable belief of danger and an unreasonable belief of danger. Tapping away our fear of any feeling, memory, belief or situation may leave your rational instincts more capable of judging the situation but it does not mean real danger no longer exists. To a large degree we are taking conscious control of your fight or flight instincts. Take this responsibility very seriously!

For example, tapping combined with misguided pride may keep you from handing your wallet or purse over to an armed thug, but by resisting you may increase the odds of the thug harming you. Your first priority is to protect your body at all costs. Having no fear combined with misguided pride or negligent thinking may jeopardize your body. But having sensible fear and sensible instincts means you exit the situation safely first, followed by the appropriate actions. In any situation, ALWAYS be aware of what you are doing! Do not get lazy, arrogant or overconfident!

Eoat Gripper

You Can Find a EOAT in Baldwin here:

 



Check the Weather in Baldwin, Michigan

Beaver Island Injection Molding Machine

How to Find a Palletizing in Beaver Island ?

Whether the fabricator’s store is large or small, the Ironworker is the backbone. The Ironworker isn’t a single machine; it is five machines united into an engineering wonder. It has much more versatility than most people would imagine. The five working sections that are involved in the make-up of this machine are a punch, a section shear, a bar shear, a plate shear, and a coper-notcher.

A number of the cheaper ironworkers are constructed to employ a fulcrum where the ram shakes back and forth, making the punch go into the succumb at a small angle. This normally leads to the erosion of the punch and die on the front rims. The higher quality machines incorporate a ram which moves in a direct vertical line and employs modifiable gibs and guidebooks to ensure a constant traveling path.

Custom Plastic Injection Molding

When you look for a End of Arm Tooling (EOAT)  that develop a Palletizing in Beaver Island, looks for experience and not only pricing.

That devotes more life to the tooling, and allows the punch to penetrate the die right in the middle in order to capitalize on the machine’s total tonnage.

When looking for a design house that designs a Palletizing in Beaver Island  don’t look just in Michigan , other States also have great providers.

Injection Moulding Manufacturers

Ergonomic Garden Tools - The Most Common Types and What to Consider When Purchasing

?

There are many different types of ergonomic garden tools. This article will cover a few of the most common ergonomic garden tools available, and will also mention a few things to look for when shopping for the tool that's right for you.

Ergonomic Hand Garden Tools

In the smaller range of ergonomic hand tools, the most common design trait is a curved handle. I've seen this design also called a radial handle. Traditional hand gardening tools force you to strain the angle of your wrist downward as you grip and push the tool into the soil. Ergonomic garden tools have a curved handle that looks like a pistol grip. This allows you to keep your wrist straight and in-line with your forearm. You than can make a much stronger fist and put more weight and strength into the tool without straining the joints or tendons of your wrist.

Another innovative design uses a straight handle shaft, about 12 inches long, that straps securely to your forearm, just below your elbow, and then uses a perpendicular grip handle at the level of your hand that you can grasp. This is a great design for individuals that have some level of disability or suffer from arthritis, because you can make use of the strength of your entire arm, distributing the weight and force throughout, instead of on your wrist and hand. You will also significantly increase the force of work you can exert on the garden tool.

1. Strength

Both the handle and tool head should be strong. Some manufacturers use a lightweight steel shaft that is coated. Others will use a professional grade fiberglass that is both lightweight and strong. Strength and weight are key to good quality ergonomic garden tools.

2. Weight

As just mentioned, weight is an important factor. There are designs that are both durable and very strong, but also light weight. You do not want to work with a heavy tool. Repetitive movements over a period of time will bring more fatigue and increase chances of injury if you use a heavy tool.

3. Quality Construction

Buying an 89 cent, two liter bottle of off-brand soda may be a good idea, but buying inexpensive, off-brand ergonomic garden tools is usually not. Cheap metals, flimsy tool attachments, weak handles, etc., are factors you need to stay away from. Pay for high quality and life-long warranties, and you will use your tools for years.

---

By Dan Fenstemaker, Inventor of the Original INTELETOOL

Injection Moulding Manufacturers

Robotic System Integration

Summary:

Cabot Microelectronics used two different FactoryFix Experts for Robot System Integration to retrofit an existing Fanuc Robot Palletizing System that had been sitting unused in their facility due to an unsuccessful installation by the original Robot Integrator. Cabot found two qualified companies to do the work on-site at their facility in Aurora, IL by posting the project on www.factoryfix.com.

FactoryFix Experts:

Compass Automation & Elite Automation

Customer Benefits:

Full System Retrofit — went from an unsuccessful installation to fully operational automated system.

Automated Production — Elite Automation programmed the system to run unattended for 3 shifts.

Added Functionality —Elite Automation also modified the system to run an additional part number.

Technologies:

Refurbished Fanuc R-2000 robot with IR vision system

Fanuc ArcMate robot with custom ultra-sonic knife tool

ATI Tool Changer System

Custom designed Piab vacuum gripper End-of-Arm Tooling

Solution:

Compass Automation, Inc worked with Cabot Microelectronics to redesign a 2 robot system to de-palletize large bags of silica powder, cut-open the bags using an automated ultra-sonic knife, and dump the powder into a large hopper. The system had been sitting idle on the customer’s floor for over a year due to a poor execution by the initial Robot Integrator. Cabot used FactoryFix to find local automation companies that had the expertise to retrofit the system and get them back on track. After posting their first project under the End of Arm Tooling Design category, they were connected with Compass who quoted and eventually won the job. Compass designed and built a complicated vacuum gripper that accommodated two different product sizes. The gripper also had to be designed with automated flappers to mimic a human shaking the bag over the hopper to make sure all of the powdered silica got out of the bag. The second robot tool that Compass was hired to design was a custom ultra-sonic knife tool that was mounted on the refurbished Fanuc Arc-Mate 100 robot. This tool was designed for ArcMate robot to cut slits into the silica bag while the R-2000 robot was holding it with the vacuum gripper.

Jacek from Elite Automation programming the R-2000 robot.

Once the two EOAT’s were built and mounted to the robots, Cabot Microelectronics needed to find another local supplier to come in and program the system (Compass had a scheduling conflict). They posted the project request on FactoryFix and were connected with Elite Automation, an automation company based out of nearby Carol Stream. Although it was a complex system, Elite Automation wrote the program and successfully ran-off the system within two weeks. Elite has since been hired by Cabot Microelectronics several more times for program modifications and upgrades.

Project Video:

Molding Design

You Can Find a EOAT in Beaver Island here:

 



Check the Weather in Beaver Island, Michigan

Beulah Robotic Arm

How to Find a Robotic Arm in Beulah ?

Whether the fabricator’s shop is large or small, the Ironworker is the backbone. The Ironworker isn’t a single machine; it is five machines united into an engineering wonder. It has much more versatility than most people would imagine. The five working sections that are involved in the make-up of this machine are a punch, a section shear, a bar shear, a plate shear, and a coper-notcher.

A number of the cheaper ironworkers are constructed to employ a fulcrum where the ram shakes back and forth, constructing the punch go into the succumb at a small angle. This normally leads to the erosion of the punch and succumb on the front rims. The higher quality machines incorporate a ram which moves in a direct vertical line and utilizes modifiable gibs and guides to assure a constant traveling route.

Eoat Gripper

When you look for a End of Arm Tooling (EOAT)  that develop a Robotic Arm in Beulah, looks for experience and not only pricing.

That devotes more life to the tooling, and allows the punch to penetrate the succumb right in the middle in order to capitalize on the machine’s total tonnage.

When looking for a design house that designs a Robotic Arm in Beulah  don’t look just in Michigan , other States also have great providers.

Robotic Arm Gripper

How Will the Chip Wars be Won?

?

Crypto Briefing

Story after story of top talent in Financial firms and Wall Street pivoting to start their own crypto and blockchain startups. The most recent is J.P. Morgan’s former head of blockchain, Amber Baldet, who has announced a new blockchain start-up called Clovyr.

Or there is this guy, who claims Bitcoin could reach as high as $50,000 by the end of 2018.

Regarding the advent of blockchain there’s a nice video here by Fortune. Amber, who most recently served as the bank’s blockchain program lead at JP Morgna Chase, is co-founding a new startup, Clovyr, that aims to help consumers, developers, and businesses explore the nascent, albeit burgeoning, world of blockchain-based, decentralized technologies.

Baldet hopes she can:

Help people think differently about decentralized application design.
  • Baldet’s post-J.P. Morgan plans have been the topic of speculation since she announced her departure from the bank in April. This is part of a growing trend, the writing is on the wall for Wall Street firms that do not remain agile, and now is the right time to pivot to the blockchain and crypto that are still somewhat nascent and could eventually disrupt financial markets and how financial services work on very fundamental levels.
Shaun Mader | FilmMagic | Getty Images

Amber won’t be the first or the last to leave the comfort of Wall Street, let’s remember where Jeff Bezos got his mathematical and strategic roots.

Baldet unveiled a Clovyr demo at the Consensus conference in Manhattan on Monday afternoon, May 14th, 2018. They are fundraising now as well.

Will Clovyr be the Apple Store for Decentralized Apps?

Baldet co-founded Clovyr with Patrick Nielsen, who led development for J.P. Morgan’s open source blockchain projects.The new company will offer something similar to an app store, but for “decentralized applications” which exist on a blockchain, points out CNBC.

Build it and they will come, we know that the blockchain is coming, even Amazon announced another major partner in its efforts on the cloud. We already knew this but Amazon’s cloud computing arm is now teaming up with startup Kaleido to help simplify blockchain technology for its clients.

Clovyr feels very much like a B2B platform dApp ecosystem in the making:

Clovyr is a decentralized application store that will host a selection of well-vetted applications alongside some in-house developer tooling designed to simplify application development for enterprises.

Seriously though, who would not want to invest in something like this?

Fortune Video

Anticipating the future is not very hard if you are a blockchain enthusiast. She is joined by Nielsen (above), former lead developer of Quorum, a JPMorgan Chase-built blockchain for business, who will serve as the concern’s chief technologist. If JP Morgan Chase is not even able to retain it’s top blockchain people, something is seriously wrong with their R&D model.

Or hang on a second, is this a spin-off play by JP Morgan itself? The report goes on to say: maintaining a “blockchain agnostic” approach to application design, Clovyr will initially provide tooling to build on both public and enterprise versions of ethereum, specifically the Quorum. These Wall Street firms know that they have to appear independent with their innovation startups to gain trust of Millennials. Someone that calls Bitcoin idiotic is probably not on the inside track of trust to the crypto hoard.

What Clovyr reminds me of is essentially a “Shopify of Crypto”, as the cofounders envision the platform serving as a neutral ground, offering a browser-like dashboard for the blockchain-curious, through which Clovyr can provide support and other services to customers according to their needs.

Does the concept make any sense to you?

Pneumatic Gripper

Intel dominated and defined the semiconductor landscape during the PC era on two complementary fronts — silicon process technology and computing architecture (x86). Through its partnership with Microsoft, Intel enjoyed a near complete monopoly over the computing landscape during the PC era. That dominance began to erode with the emergence of two Segment Zero markets (Link) for Intel — embedded computing and mobile computing. The company that under the leadership of Andy Grove had successfully identified and vanquished at least two prior disruptive threats (Japanese memory makers in the 1980s and low cost PCs in the early 1990s) failed to successfully prepare for the next disruption — mobile computing and the ecosystem pioneered by ARM, the leader in low-cost/low-power architecture. While Intel pioneered the era of the standalone CPU with a vertically integrated business model, ARM enabled a massive lateral design/foundry ecosystem and pioneered the era of the mobile SoC (system-on-a-chip).

CPU vs. SoC

In the CPU space, chip functionality is largely determined by the computing core (e.g. Pentium, Athlon) and transistor performance is the critical metric. In the SoC space, the core is just one among a variety of IP blocks that are used to independently deliver functionality. Intel’s foray into SoC technology started in the early 2000s and was largely a response to the success of the foundry ecosystem. However, Intel’s SoC process technology has typically been implemented 1–2 years behind its mainstream CPU technology, which historically has focused on transistor scaling and performance. The foundries within the ecosystem instead focused on integrating disparate functional IP blocks on a chip while also aggressively scaling interconnect density.

The semiconductor industry today is increasingly driven by low-power consumer electronics (primarily smartphones) and SoC shipments now dominate total silicon volume. The sheer volume of desktop class computing chips like Apple A9 SoCs shipped to date has in turn dramatically improved the competitiveness of the foundry ecosystem (led by TSMC) compared to Intel. Until a few years ago, Intel’s process technology lead was unquestioned. That lead is now greatly diminished as the foundry ecosystem is on track to ship more 64 bit SoC chips than Intel by the end of this year.

The ascendance of ARM has not only displaced Intel’s leadership on the architecture front (x86) but indirectly, also on the process technology front by enabling the foundry ecosystem to ship incredibly large volumes of leading edge silicon and dramatically speeding up the manufacturing yield learning curve. Intel was late in recognizing the importance of the SoC and now finds itself playing catch-up to a strong ecosystem led by ARM on the architecture front and TSMC on the silicon process technology front.

Compounding this trend further is the reality that after 50 years of delivering consistent gains in power, performance and cost; transistor scaling is finally entering an era of diminishing returns where further shrinking the device is not only costly, but provides incremental gains in performance and power.

Meanwhile, the ARM ecosystem is also steadily making inroads into the high-end space traditionally dominated by Intel. Several new tablet and laptop computers (e.g. Google Pixel C) use SoC chips designed by fabless companies instead of CPU solutions from Intel. Over time, SoCs became much more powerful and competitive and now pose a meaningful threat to the standalone CPU. The predominance of the Intel-Microsoft partnership based on x86 architecture is waning and a huge swath of the mobile computing space is now supported by low cost Chinese design houses like MediaTek, AllWinner, RockChip and Spreadtrum that use ARM architecture and foundries like TSMC, SMIC or UMC.

The emergence of the SoC was thus a strategic inflection point for both Intel and the ARM ecosystem alike. While the silicon landscape during the PC era was defined by Intel and the CPU, it is fair to say that the silicon landscape during the mobile era continues to be defined by the SoC and the foundry ecosystem led by ARM and TSMC. In many ways, Intel’s ability to compete in the SoC space will determine the direction of the chip wars in the next wave of computing (IoT).

Transistor Technology

The process technology underlying CPUs and SoCs is similar, however the design points for each can be vastly different. For example, a CPU design requires fewer transistor variants spanning a limited range of leakage and speed. On the other hand, SoC designs require many more transistor variants spanning a much wider range of leakage and speed. SoC technology also needs to support higher supply voltages for IO devices (e.g. 1.8V, 3.3V) in addition to the nominal supply voltage for core devices (e.g. 0.9V) These differences, though subtle, require very different mindsets in transistor design and process architecture.

Intel’s focus on transistor performance can be traced back to the height of the PC wars when the benchmark was clock speed. While Intel focused on transistor performance, the foundries adapted Intel’s transistor innovations for their own SoC integration needs. In addition, they aggressively pursued metal density scaling and cost reduction. While Intel pursued a limited vertical functional integration, the foundries developed a lateral ecosystem and designed transistors for a variety of vendors that independently optimized functionality for each IP block (CPU, GPU, radio, modem, GPS, IO, SERDES, etc.).

This vast ecosystem of existing design IP is now a significant influence on the adoption of the next transistor architecture. Arguably, the foundries are today better positioned for the SoC era. By the end of 2015, TSMC will have shipped well over 100 million units of Apple’s A9 SoC. These processors are made in 16nm technology and will set new benchmarks for cost, power and connectivity features. The Apple A9 processor is possibly the most highly integrated SoC running on the most advanced silicon process technology (at TSMC and also Samsung). Intel’s advantage at the transistor level thus allowed it to win the CPU space, but the ecosystem has the advantage at the system level and is poised to win the SoC space.

In the mobile and IoT era, packing as many features on a chip as possible at the lowest integrated system cost and power will win. The transistor technology that is most compatible with all the IP needs of a complex SoC at the lowest cost will thus have the upper hand.

The Post-PC Era: Intel in an Open Ecosystem

The slowdown in the pace of Moore’s Law, the emerging importance of the SoC and the rapid growth of the mobile market all tend to favor an open, plug-and-play foundry and design ecosystem. One could expect that the ecosystem developing around ARM will continue to nip at Intel’s core markets as the development of ARM-based processors for laptops and servers accelerates. This emerging threat to Intel and Intel’s response to it will define the industry over the coming decade.

The operating system (OS) war between Microsoft and Apple in the 1980s came to define the PC and software industries. Microsoft’s open ecosystem model won as Windows became the de-facto OS for machines made by all kinds of PC makers. While Microsoft promoted an open ecosystem in the larger PC industry, ironically it spawned a closed ecosystem within the semiconductor industry. The Wintel alliance ensured that Windows only ran on x86 architecture which was pioneered and owned by Intel. The closed ecosystem hugely benefited Intel as it went on almost unchallenged to win the desktop, laptop and server space (AMD also used x86 yet could never match Intel’s scale or manufacturing expertise). A hallmark of the post-PC era is the emergence of an open ecosystem within the semiconductor industry.

Unlike the Windows/x86 dominance of the past, the post-PC era is being defined by competing OS options (iOS, Android or Windows) and competing processor architectures (x86 or ARM). Today, the momentum is in favor of ARM-based operating systems as the vast majority of mobile devices being shipped today run iOS or Android (ARM architecture).

The chip wars will be fought in this fragmented and open ecosystem on three fronts — SoC (system integration), CPU (core architecture) and silicon (foundry technology). While performance and power will continue to be important benchmarks, the open ecosystem supporting a worldwide consumer market will make cost a key success metric on each battlefront.

Battlefront #1 — SoC (System Integration)

In the mobile SoC space, the battle for processor architecture will be between Intel on the one hand and incumbents like Qualcomm, Samsung and Apple on the other. In the mobile, power constrained space, it is more efficient to integrate a variety of hardware accelerators on a single chip to deliver custom functionality as opposed to implementing a general purpose core serving most functions. Low power cores are supplemented with elements as disparate as an on-chip radio, global positioning system (GPS), modem, image and audio/video processor, universal serial bus (USB) connectivity and a graphics processing unit (GPU). An open ecosystem is far more cost-effective for such modular, plug-and-play system-level integration.

A typical CPU design (Intel Core-M) dominated by core/graphics compared to a highly integrated SoC (NVIDIA Tegra 2). The integrated SoC design has obvious advantages in mobile formfactors.

Historically, Intel, being an integrated device manufacturer (IDM) has independently designed most of the functional IP blocks, while ensuring that each uses Intel transistor technology and process design rules. Intel’s process technology leadership has benefited it enormously in the CPU space giving its designers access to best-in-class transistor performance. However, Intel’s ability to compete in the mobile SoC space will be determined by how well it can re-engineer its CPU process technology to meet the diverse needs of a complex mobile SoC.

If Intel can successfully design and manufacture 14nm and 10nm processes that span the full range of the performance-power spectrum required for mobile SoC applications, it will have an edge over the competition. But for Intel to compete effectively in the mobile SoC space, it will also need to offer a cost advantage. Average Selling Price (ASP) in the SoC space is a fraction of that in the CPU space. While fabless Apple can drive the best possible deal from competing foundries, IDM Intel needs to ensure that its volumes and ASPs are high enough to recoup its own development and manufacturing CapEx.

Intel may try to enhance its SoC functionality offering by way of more acquisitions like Infineon Wireless. But post-merger, porting Infineon’s foundry standard design rules to Intel’s proprietary design rules will be non-trivial (In 2015, nearly 5 years after the acquisition, Intel is yet to port Infineon’s modem chips to their own fabs and continues to make them at TSMC!). By contrast, the Qualcomm acquisition of Atheros likely proved to be more seamless since the IP was from the open ecosystem and already foundry compatible.

Battlefront #2 — CPU (Core Architecture)

The main battle on the CPU front is between Intel/x86 and ARM architecture. While Intel historically has had the upper hand in performance, ARM-designed cores have delivered superior performance/watt.

To effectively compete against ARM, Intel will need to design its low-power Atom cores in the most power-efficient way possible. To design a true low-power core, Intel may need to decouple the Atom from legacy x86-based architecture and develop a new ground-up design that delivers highly competitive performance/watt.

Intel will also have to be in aggressive catch-up mode as it tries to reverse the momentum of an already large, established and robust ARM software ecosystem. In the initial years of the PC era, as x86 became the predominant CPU architecture, an entire ecosystem of application software was spawned that was designed to run solely on x86. This effectively precluded or seriously hindered competing architectures like PowerPC from ever gaining a foothold in the marketplace. Analogously, in the present day, ARM architecture is significantly further along in achieving critical mass in the mobile SoC space. The prevalence of ARM in a range of post-PC devices from smartphones and tablets (90% market share) to televisions and cars has placed ARM in a commanding position to inhibit the newer Intel Atom architecture from achieving traction. Practically speaking, for Intel to gain a meaningful share in the mobile market, it now has to ensure compatibility with the ARM software ecosystem. This again, will force Intel to compete on price which will limit how much revenue it can eventually generate. This is a dynamic that Intel never had to face in the PC segment.

Battlefront #3 — Silicon (Foundry Technology)

Intel’s ability to make the best performing transistor at the highest possible yields and volumes is unparalleled. This capability served it immensely well in the closed ecosystem when Intel was essentially competing against itself in the quest to make a smaller and faster transistor. In the closed ecosystem, performance trumped power; and design flexibility and high ASPs ensured that development cost was not a significant limiter.

In the open ecosystem, however, the ability to integrate disparate functional accelerators in the most power-efficient and cost-effective manner is paramount. As an example, TSMC is able to deliver the highly successful and functional A9 processor for Apple using a state-of-the-art 16nm transistor process and integrate a variety of complex IP blocks while keeping the ASP under $20. TSMC’s minimum metal pitch at the 16nm node is larger (i.e. less dense) than that of Intel at the more advanced 14nm node, yet the A9 SoC can offer better power efficiency than a comparable 14nm CPU at an acceptable performance point and much lower price point and a much smaller form-factor.

In the post-PC era, mobile and IoT computing will have a larger influence on the semiconductor landscape. The success metrics in the new landscape are not just higher transistor performance but higher system functionality, lower system cost and lower power.

Based on the above discussion and judgment, the following trends are likely to define the semiconductor industry over the next decade.

  1. Shrinking pool of advanced semiconductor fabs: The economics of Moore’s Law and the advent of mobile computing have led to a dramatic reduction in the number of advanced semiconductor manufacturing sources. Just 3 major entitities (Intel, Samsung, TSMC) now offer unique 16nm or advanced technology. (Globalfoundries is effectively just a manufacturing partner for Samsung). A wildcard here is SMIC (Semiconductor Manufacturing International Corporation, Shanghai). Even though it is a relative newcomer, SMIC is extremely driven and has the full backing of the Chinese government which has made advanced semiconductor manufacturing a national priority. SMICs entry at 14nm (by 2020) may change the foundry landscape by dramatically altering silicon wafer price-points.
  2. Making things smaller doesn't help much anymore: The 28nm node will be the longest running planar transistor technology. In a departure from prior technologies, and in response to plateauing transistor cost, the leading foundry (TSMC) has developed over 5 flavors of the technology for all applications ranging from high performance 28HPM (FPGA, GPU, mobile SoC) to ultra-low power 28ULP (IoT edge computing). As the mobile computing era matures and the IoT computing era emerges, majority of the applications will be served by 28nm or older technology. As technology development lifecycles get longer and product lifecycles get shorter, foundries will try to extract all the goodness in an existing transistor technology before moving to the next one.
  3. Even fewer applications for advanced technologies: Only a minority of applications (e.g. high performance computing, AI/AR, machine learning, computer vision) will migrate to using sub-10nm and lower technology nodes. And these advanced nodes will also be long lived with multiple variants serving disparate power/performance/cost points.
  4. Intel CPU leadership: Intel will continue to dominate the single thread/high performance CPU/server segment, albeit with increasing competition from the ARM ecosystem. Intel’s acquisition of Altera is a defensive move aimed at creating a moat around its server leadership. However, the next five years will likely see the emergence of competitive ARM based servers. Using an open ecosystem with customizable IP will enable significant cost and power reduction for these new entrants.
  5. Lego block on-chip integration: In the power and cost competitive IoT era, on-chip integration of hardware accelerators (modem, CPU, graphics, etc) will continue to be extremely efficient. Compared to centralized CPU/GPU cores, SoCs will be far more effective, especially in the smartphone, tablet and convertible form-factors. As silicon scaling plateaus, packing as many disparate functional blocks as possible on a chip within a given transistor budget at the lowest integrated system cost and power will win. Companies will try to expand their footprint by capturing more real estate on the chip, either through consolidation or on their own.
  6. Ascendance of the SoC: Intel’s 14nm CPU (Skylake, 2015) and Apple/TSMC’s 16nm SoC (Apple A9, 2015) are two marquee technologies/products that will provide a barometer on the semiconductor landscape. Several benchmarking results indicate that the A9 is perhaps the most efficient mobile SoC with unparalleled performance/power metrics. This match-up will have remarkable implications — not only will it validate the rise of Apple as the dominant SoC design team, it will also suggest a vulnerability in Intel’s process technology leadership. It suggests that TSMC could go toe-to-toe with Intel on radical and highly complex transistor architectures (16/14nm tri-gate), while also supporting best-in-class SoC technology which is the enabling platform for mobile and IoT computing. Intel will need to dramatically improve its SoC offering in the years to come in order to be competitive in the SoC/IoT space.
  7. Slowing cadence of Moore’s Law: Two technologies that have the potential to significantly influence the economics of Moore’s Law and disrupt the industry cost model are (a) 450mm wafer size and (b) EUV lithography. However, a glut of fully depreciated 300mm fab infrastructure and decades long slow progress in the EUV tooling roadmap will make it a difficult value proposition at least in the foreseeable future. Conventional Moore’s Law scaling is likely to give way to more orthogonal scaling approaches (More-than-Moore) including 3D chip stacking and system/package level integration of heterogeneous chips.
Injection Molding Materials

You Can Find a EOAT in Beulah here:

 



Check the Weather in Beulah, Michigan

Brant Plastic Manufacturers

How to Find a Injection Molding Companies in Brant ?

Whether the fabricator’s shop is large or small, the Ironworker is the backbone. The Ironworker isn’t a single machine; it is five machines united into an engineering wonder. It has much more versatility than most people would imagine. The five working sections that are involved in the make-up of this machine are a punch, a section shear, a bar shear, a plate shear, and a coper-notcher.

A number of the cheaper ironworkers are constructed to employ a fulcrum where the ram shakes back and forth, constructing the punch go into the succumb at a small angle. This normally leads to the eroding of the punch and succumb on the front rims. The higher quality machines integrate a ram which moves in a direct vertical line and utilizes modifiable gibs and guides to insure a constant traveling route.

Custom Plastic Injection Molding

When you look for a End of Arm Tooling (EOAT)  that develop a Injection Molding Companies in Brant, looks for experience and not only pricing.

That devotes more life to the tooling, and allows the punch to penetrate the die right in the middle in order to capitalize on the machine’s total tonnage.

When looking for a design house that designs a Injection Molding Companies in Brant  don’t look just in Michigan , other States also have great providers.

Eoat Gripper

Real-life AWS infrastructure cost optimization strategy

?

Obviously enough, one of the first things many people want to know when getting started with scrolling as a hobby is what saw to buy. Whether you are looking to purchase your first scroll saw, or you are looking to upgrade to a better one, there are many things to consider. In this article I will attempt to touch on all aspects so that you are able to make an informed decision. I will also make some recommendations based on personal experience and what I feel is the general consensus of the scroll sawyers I have discussed the matter with.

Important Considerations

Blade Changing and Blade Holders: The saw should accept standard 5" pinless blades. A lot of scrollwork simply cannot be done with a saw that requires pinned blades. While pinned blades have some advantages, they have one very big disadvantage: You can't cut any small inside detail cuts since you have to drill a very big hole to get the blade's pin through.

Also, how easy is it to change a blade? Is a tool required for this? Some scroll saw projects have hundreds of holes. This means you have to remove one end of the blade from the holder and thread it through the wood and re-mount it in the holder more times than you can count. Be sure the process is comfortable and relatively easy to do. A saw in which the arm can be raised and which holds itself in this position is most desirable as it makes this process much easier as do tool-less blade holders.

Variable speed: A great many saws offer variable speed and you should not have a problem finding this feature in any price range. Sometimes you will want to slow the blade down just to cut slower, other times you must slow it down to prevent the blade from burning the edges of the wood as you cut. Some scroll saws require belt changing to change speeds. Personally, I would highly recommend a saw an electronic speed control.

Vibration: Vibration is very distracting when cutting and must be kept to a bare minimum. Some saws inherently vibrate more by design. This feature tends to be very much dependent on the cost of the particular saw. Vibration can be reduced by mounting the saw to a stand. A sturdily mounted saw and heavier saw/stand combination will reduce vibration. Many companies offer stands purpose built for their saws.

Size Specifications: Manufacturers often list the maximum cutting thickness of their saws. Since this is always more than 2", you can ignore this as you likely will never want to cut anything thicker than that on a scroll saw.

The depth of the throat however is something you may want to consider if you think you will be cutting very large projects. A small throat will limit how big of a piece you can swing around on the table while you cut. For many this is not a very big deal since it is somewhat difficult and unpleasant to swing around a big piece of wood on a scroll saw. This limit can also be circumvented by the use of spiral blades which don't require the work to be rotated at all.

A most notable difference between the Excalibur and other saws is that the head of the saw tilts rather than the table. This is a nice advantage if you intend to do a lot of angled cutting. The one feature that I personally am leery about is that you only have a quick release for the tension at the front of the saw's upper arm and the fine adjustment is at the back of the arm. This is a relatively recent change to the saw however I have not seen any negative feedback about this setup. Theoretically, once you have set the fine adjustment, you don't have to adjust it very often and you just need the quick release when undoing/redoing the blade to feed it through your project.

These saws are manufactured by General International, which has a reputation for quality.

Other notable mentions RBI and Eclipse both offer high end saws with great performance and low vibration. You may want to check these saws out if you can afford them. Since they are out of most people's price range, I have not heard a whole lot of feedback on them. In my opinion, many of these models do however have inconveniently located controls and/or require tools for blade changes which do give me cause for concern.

Hegner offers four different models starting at about $700 and going all the way to $2400. The lowest end model "Multimax 14-E" is only single speed which I would definitely stay away from. In my opinion there are several better choices for a comparable or cheaper price. The $2400 industrial "Polymax" model requires belt changing to change the speed which is an inconvenience. Because of this issue and the high price tag, I would only consider this model for a truly industrial purpose. This leaves us with the Mutimax 18-V and 22-V models to consider.

All Hegner saws require tools for blade changes. This fact, in addition to what I would personally consider an inconvenient control layout would make me think twice about a Hegner. That being said, most people who own Hegners are very happy with the quality and usability of their saws. Since I have not personally used one, I will leave this matter for your further consideration if you can afford a saw in this price range.

Conclusion

I hope this article has provided you with enough information to allow you to make the best possible investment of your money so that you can start with or upgrade to a scroll saw that will provide you years of scrolling pleasure.

End Of Arm Tooling Parts

By Rod Vagg

ARM: A Quick Primer

ARM is a tricky beast to describe because it’s more than one thing. In common parlance, we use it to describe a CPU architecture, akin to x86 from Intel and AMD. The ARM name comes from its designer, ARM Holdings, but they don’t actually make the hardware, unlike Intel and AMD. ARM is primarily an intellectual property company which licenses their technology to manufacturers to form a vibrant ecosystem of processor and SoC (System on a Chip) products.

An ecosystem of manufacturers

Companies such as Samsung, Qualcomm, Broadcom and even AMD (traditionally known for their x86 products) license core CPU designs from ARM, largely made up of the “Cortex” range. A number of CPU design licensees release Cortex-based processors under their own branding, which is where you see familiar names such as the Qualcomm Snapdragon, the Samsung Exynos or Nvidia Tegra.

In addition, ARM offers an architectural license that gives licensees permission to design their own CPUs that fully comply with the ARM architecture to ensure instruction set architecture (ISA) compatibility. Companies such as Applied Micro and Cavium currently hold architectural licenses and are producing their own processor designs. Apple uses an architectural license to produce its Ax series of processors, including the A7 and A8 which power the current iPhone and iPad range.

The ARM architecture

Due to the compact nature of the ARM architecture, it has traditionally been used for small devices. ARM processor designs tend to focus on efficiency as their current primary uses are in devices where power draw is a major concern. Most smartphones and tablets in the market today are based around ARM processors and they are even showing up in laptops, with many of the current Chromebook range using ARM processors.

ARM’s architecture designs are broken up in to generational versions. The most common ARM architecture generation used in smartphones, tablets and other small computers today is ARMv7. For instance, the newest incarnation of the Raspberry Pi uses an ARMv7 processor, while the original Pi used an ARMv6 processor, the previous generation.

There’s a new generation that’s starting to roll out, ARMv8 and this represents a major shift in architecture design and also a shift in the commercial potential that ARM Holdings sees for its processors.

The HiKey development board from 96Boards using an HiSilicon Kirin 6220 eight-core ARMv8 Cortex-A53 CPU

Until now, ARM’s range of processors and architecture designs have been 32-bit, meaning they have limitations in their ability to scale to uses beyond small devices. But even our smartphones are starting to push up against the barriers that 32-bit processors present, most notably the limitations to the amount of RAM you can couple with the processor. ARMv8 is a new 64-bit design that alleviates the barriers presented by 32-bits. The ARM family of processors already reaches deep into the low-power and small-size end of the market (as demonstrated b the Cortex-M0+ pictured above), but with ARMv8, there is a new target: the server market.

ARM on the Server

The phenomenal success of the Raspberry Pi saw the dawn of a whole new class of computers gaining wide acceptance: “single-board computers”. There is now a huge range of products in this market, all vying for the attention of hobbyists and commercial users alike. Even Intel is in on the game with their low-power x86 incarnation, the Atom. The low cost and surprising versatility of these small computers have lead to some interesting new uses. DataStax likes to show off their 32-node Rasperry Pi Cassandra Cluster as a way to demonstrate the versatility of Cassandra but even more, it shows the potential uses that low-cost single-board computers can be put to. Online Labs have rolled out a new IaaS (Infrastructure as a Service) product named Scaleway based completely around ARMv7 servers and are finding strong interest from customers wanting smaller and simpler cloud infrastructure.

The DataStax demonstration 32-node Rasperry Pi Cassandra Cluster

miniNodes, another IaaS company, has jumped straight to ARMv8 in its offering by using early development ARMv8 boards. The University of Utah, in its contribution to the scientific computing cloud research project CloudLab, are rolling out a cluster of 315 HP Moonshot m400 cartridges, with which HP are claiming the title of “The World’s First Enterprise-ready 64-bit ARM Server”.

Also getting in on the ARMv8 hardware action is Gigabyte, Lenovo, Hyve Solutions, SoftIron, StackVelocity and E4 who specifically target HPC applications. As 2015 rolls on, expect a flourish of new hardware to appear, pushing us to rethink some traditional approaches.

The HP Moonshot m400 ARMv8 cartridge

The new ARMv8 processors are intended to further bridge the gap between traditional ARM uses and the new forms of server computers that there is an obvious demand for. Their low-power profile will mean that their natural target will still be smaller servers but we will likely see many cluster-style products come on to the market where many ARMv8 boards are combined into a unified cluster.

The Software Stack

Just as we are seeing shifts in the hardware market, with new demand for clusters of smaller servers rather than simply continuing to push at Moore’s Law to make servers ever-bigger, we are also seeing shifts in the traditional trajectory of the software stack. Monolithic applications are now viewed as both business and technical risks. SOA (Service Oriented Architecture) is the new best-practice with experimentation all the way down to micro-services. We’re in the midst of a great ‘unbundling’ in the software world.

While the JVM is right at the heart of the monolithic software stack and the tooling that surrounds it, Node, or server-side JavaScript, is arguably at the heart of the new SOA stack. Node’s small and nimble runtime profile along with its overriding culture of modularity make it a perfect fit for a transition to the composition of applications from smaller, focused, services.

There is an interesting intersection between the changes in the hardware market and the changes in best-practice software development. Smaller, more nimble software is perfectly suited to smaller, more nimble and low-power hardware. What’s more, Node’s development model encourages developers to think multi-process from the beginning because we know that without the crutch of threads, the only way we can scale our applications is to multiply the number of processes (have you ever noticed how you rarely hear Node developers talk about “sticky-sessions” while Java developers obsess about them?). This means that Node applications scale as easily across clusters of servers as they do within a single server. Not only does the Node development model buy you free scalability, it also buys you resilience by fitting better on larger numbers of smaller servers instead of smaller numbers of larger servers as you typically see in the JVM world (although, the typical Node application performance profile means that you need significantly less total hardware investment as well).

One of the common patterns that NodeSource encounters across the enterprise as companies start waking up to the potential that Node offers them is that they need to start rethinking their hardware needs. Typically, large companies will have a homogeneous production environment, with one or two types of server available for deploying applications. Commonly these are tuned to the needs of the JVM and other monolithic application stacks so there is a priority placed the on speed and size of each hardware unit. An average server might have 16 cores and 32G of RAM and be a perfect match for a JVM application that makes liberal use of threads and is a natural memory hog. Unfortunately, this doesn’t translate very well to Node, particularly on the memory side. So we see a lot of wasted hardware in these environments with architects exploring new ways to make use of all of the free RAM they now have available. This is not ideal from a cost perspective but understandable where Node is only at the beginning of its journey into these environments.

Node and ARM: A Perfect Match

As argued above, Node is a great fit for the changes occurring in the hardware stack:

  1. Node isn’t a resource hog, it’s at home in smaller environments with its low memory profile and single-threaded nature.
  2. Node is nimble; for example, we advise our clients to kill & quickly restart when their applications enter an unexpected-error state. You can’t do this with a runtime that takes minutes to properly start and warm-up.
  3. Node’s development model and culture is naturally SOA; if you’re building a large application and it’s not made up of small services then you’re doing Node wrong. Node applications are generally scalable by default.

Another important factor here is Node’s use of V8 as a JavaScript foundation. From its early days, the Chromium project has treated the ARM platform as one of its primary targets. Chrome is on every new Android-based phone and tablet and is obviously a foundational component of Chromebooks. V8 is already heavily optimized for ARM and is moving in lock-step with ARM because it’s in the interests of both ARM and Google to do so.

io.js, the community fork of Node.js, released its 1.0 earlier this year. ARM has been second-class for Node.js until now so we encouraged a new focus on ARM as a first-class platform target for the io.js project. ARM hardware has been a fixture in the io.js CI system from the beginning and the project has been shipping ARM binaries since 1.0. Today you can download both ARMv6 and ARMv7 optimized binaries for io.js releases and nightlies right from the downloads directory. Through this focus, io.js has even been able to feed patches back in V8 to fix and improve support for ARM.

Because io.js is using current V8 releases and we have made it clear that ARM as a platform with primary support, ARM Holdings has taken an interest in the project. It’s clear that they see similar synergies to us between Node and ARM hardware, particularly with their new focus on server use of their architecture. ARM has stated publicly that their goal is to carve out 20% of the server market with its new architecture within five years, up from less than 1% today.

ARMv6 and ARMv7 boards serving in the current io.js ARM test and build cluster

We have been working with ARM to get access to test hardware for the io.js CI system to bring the codebase up to scratch on the new ARMv8 architecture. The not-for-profit Linaro organization was set up by ARM and its partners to work on bringing better ARMv7 and ARMv8 support to open source software. The organization maintains a server cluster which the io.js project currently has access to for ARMv8 test hardware and has used this resource to understand and solve the technical hurdles involved. io.js is now shipping experimental 64-bit ARMv8 binaries in its nightly distribution channel. By the time single-board ARMv8 computers are available on the general market there will also be release builds of io.js available for use. Keep an eye on 96Boards, a project by Linaro, if you are interested in affordable ARMv8 hardware.

Getting Real

Of course, any embrace of the combination of smaller servers and Node for the enterprise is likely to be part of a longer, multi-year strategy. As of right now, Node adoption is still in the early stages at most companies that are choosing to embrace it. Their immediate concerns are more about the basic architecture questions relating to unbundling monolithic structures. As new SOA models emerge, questions about the optimization of hardware platforms will arise and it’s likely that ARM will be in serious consideration.

Aside from enterprise concerns, it’s clear that ARM at least has a future in new-style, low-cost cloud platforms that may be very attractive to start-ups and those of us who are looking for cheap hosting for our side-projects.

Node is still young, and adapting to a changing hardware landscape should be easy. Through io.js, Node’s future on ARM hardware is looking very positive. NodeSource will be keenly watching how the community and companies, both small and large, react to the new possibilities as they emerge.

Eoat Gripper

You Can Find a EOAT in Brant here:

 



Check the Weather in Brant, Michigan

Buchanan Plastic Manufacturers

How to Find a Plastic Manufacturers in Buchanan ?

Whether the fabricator’s store is large or small, the Ironworker is the backbone. The Ironworker isn’t a single machine; it is five machines united into an engineering wonder. It has much more versatility than most people would imagine. The five working sections that are involved in the make-up of this machine are a punch, a section shear, a bar shear, a plate shear, and a coper-notcher.

A number of the cheaper ironworkers are constructed to employ a fulcrum where the ram shakes back and forth, making the punch go into the die at a small angle. This normally leads to the erosion of the punch and die on the front rims. The higher quality machines integrate a ram which moves in a direct vertical line and utilizes modifiable gibs and guides to guarantee a constant traveling path.

Mouldable Plastic

When you look for a End of Arm Tooling (EOAT)  that develop a Plastic Manufacturers in Buchanan, looks for experience and not only pricing.

That devotes more life to the tooling, and allows the punch to penetrate the die right in the middle in order to capitalize on the machine’s total tonnage.

When looking for a design house that designs a Plastic Manufacturers in Buchanan  don’t look just in Michigan , other States also have great providers.

Injection Moulding Machine Price

How to Repair Sprinklers

?

This job is among one of my favorites. It’s because the entire project was mine. I started by going out to their facility and seeing their inefficiencies. One cell that they were very excited to revamp was their Silica dump cell. I was able to come up with the initial concept, quote the project for materials and labor, and then do the engineering myself. I did, not only the mechanical design and detailing, but also the electrical and pneumatic schematics. I felt in charge of the whole thing- high risk, but high reward.

A HUGE 6 axis robot (ok, not that huge, I’ve used bigger) but an R2000 robot picks up these paper bags filled with Silica. The end-of-arm-tooling (EOAT) used vacuum suction to hold onto the bag.

Solidworks Rendering of EOAT

It bring it over to a hopper, where a smaller robot uses a knife to cut the bags. The larger robot then flips it’s tooling to dump the Silica into a hopper. Seems pretty simple and for the most part it was. However, the Silica is so densely packed into the bags that even when the bags were cut wide open, the Silica wouldn’t dump. To help the Silica loosen and fall, we stick needles into the bag and blow air through these probes which moves the Silica powder around. We then (for a lack of engineering terms) flap the bag to further empty the Silica. It may sound tedious, but any powder or residue left in the bag is money wasted for the company.

An SMC slide cylinder pushed the air probes through the paper bag, and the fittings attached to the other side provided air to go through to the holes in the probe.

Another part of the project was to add a tool changer to the smaller robot. It was originally just equipped with the knife, but by adding a tool changer with a “Silica break tool” the robot was able to then go into the hopper and break up large clumps of Silica helping the contents of the hopper drain. Imagine a giant potato smasher. (Which is in fact what we ended up often calling the tool.)

Potato Smasher Robot

I had a lot of fun working with my machinist and builder on this project. I did everything I could to help them succeed, but also knew they had my back on this as well. I understand that that dynamic not all that common in the work place, so I really appreciated it. The install is happening currently and now the programmer is up to bat. The EOAT has a camera and laser to locate the bag. The camera locates the XY location of the bag and the laser the Z (height) location. I can’t wait for the tooling to be fully power, programmed, and running. I really think the customer will be happy with this addition.

Injection Molding Cost

An excavator is an engineering vehicle that is used for digging or refilling of big holes. The basic structure of an excavator comprises of the arm, the bucket and tracks. The drive and power source of the excavator is one of the major components of this equipment.

Basically, excavators run on diesel as the main power source since it produces a higher horsepower compared to gasoline. Also, diesel is more suited for heavy duty jobs to power the engine that drives the whole machine. This means that it is responsible for powering the hydraulic arm for digging and lifting mechanism as well as the tracks that are used for its mobility.

The first task to be taken care of when operating an excavator is controlling the dozer blade. First, you have to lower the controls on the left hand into position before putting on the safety belt. The next task is controlling the bulldozer blade by moving it up and down to position the blade securely into the ground for stability. The bucket at the end of the arm is the controlled by use of the joystick to perform different operations such as digging or scooping. Safety should however be highly exercised whenever you operate an excavator to avoid any mishaps.

Injection Moulding Manufacturers

You Can Find a EOAT in Buchanan here:

 



Check the Weather in Buchanan, Michigan

Capac Plastic Injection Molding

How to Find a Plastic Manufacturers in Capac ?

Whether the fabricator’s store is large or small, the Ironworker is the backbone. The Ironworker isn’t a single machine; it is five machines united into an engineering wonder. It has much more versatility than most people would imagine. The five working sections that are involved in the make-up of this machine are a punch, a section shear, a bar shear, a plate shear, and a coper-notcher.

A number of the cheaper ironworkers are constructed to employ a fulcrum where the ram shakes back and forth, constructing the punch go into the die at a small angle. This normally leads to the erosion of the punch and succumb on the front rims. The higher quality machines integrate a ram which moves in a direct vertical line and utilizes modifiable gibs and guides to insure a constant traveling path.

Injection Molding Materials

When you look for a End of Arm Tooling (EOAT)  that develop a Plastic Manufacturers in Capac, looks for experience and not only pricing.

That dedicates more life to the tooling, and allows the punch to penetrate the die right in the middle in order to capitalize on the machine’s total tonnage.

When looking for a design house that designs a Plastic Manufacturers in Capac  don’t look just in Michigan , other States also have great providers.

Vacuum Gripper

How Will the Chip Wars be Won?

?

This job is among one of my favorites. It’s because the entire project was mine. I started by going out to their facility and seeing their inefficiencies. One cell that they were very excited to revamp was their Silica dump cell. I was able to come up with the initial concept, quote the project for materials and labor, and then do the engineering myself. I did, not only the mechanical design and detailing, but also the electrical and pneumatic schematics. I felt in charge of the whole thing- high risk, but high reward.

A HUGE 6 axis robot (ok, not that huge, I’ve used bigger) but an R2000 robot picks up these paper bags filled with Silica. The end-of-arm-tooling (EOAT) used vacuum suction to hold onto the bag.

Solidworks Rendering of EOAT

It bring it over to a hopper, where a smaller robot uses a knife to cut the bags. The larger robot then flips it’s tooling to dump the Silica into a hopper. Seems pretty simple and for the most part it was. However, the Silica is so densely packed into the bags that even when the bags were cut wide open, the Silica wouldn’t dump. To help the Silica loosen and fall, we stick needles into the bag and blow air through these probes which moves the Silica powder around. We then (for a lack of engineering terms) flap the bag to further empty the Silica. It may sound tedious, but any powder or residue left in the bag is money wasted for the company.

An SMC slide cylinder pushed the air probes through the paper bag, and the fittings attached to the other side provided air to go through to the holes in the probe.

Another part of the project was to add a tool changer to the smaller robot. It was originally just equipped with the knife, but by adding a tool changer with a “Silica break tool” the robot was able to then go into the hopper and break up large clumps of Silica helping the contents of the hopper drain. Imagine a giant potato smasher. (Which is in fact what we ended up often calling the tool.)

Potato Smasher Robot

I had a lot of fun working with my machinist and builder on this project. I did everything I could to help them succeed, but also knew they had my back on this as well. I understand that that dynamic not all that common in the work place, so I really appreciated it. The install is happening currently and now the programmer is up to bat. The EOAT has a camera and laser to locate the bag. The camera locates the XY location of the bag and the laser the Z (height) location. I can’t wait for the tooling to be fully power, programmed, and running. I really think the customer will be happy with this addition.

Pneumatic Gripper

Vacuum pumps, which are the order of the day for household and industrial uses, often need repair. Dealers of vacuum pumps offer repair and maintenance at the time of purchase, as part of warranty or otherwise. Repair work is frequently undertaken by the manufacturers of particular brands, who often know the gadgets better. Otherwise, repair kits are available, with which an individual pump owner can repair the pump him- or herself.

Repair kits are available from numerous manufacturers and are an important part for users of vacuum pumps. If one volunteers to go through the "do-it-yourself" path before undertaking repairs, the pump should be sent to a detoxification center, if toxic substances were used in the pump earlier. Workspace, lots of emery paper, sealants, cleaning solvent, new oil, and facilities for disposal of the used oil are essential aspects. A manufacturer's pump repair kit can cost about $400, and some brands cost up to $900. The kit contains a bag of gaskets, shaft seals, and ""O"" rings. Other items that will be needed include a pump repair stand, hammer, cigarette paper, and most likely a puller to remove the drive pulley.

Incidentally, it was found that air consumption could be reduced by 98 percent when a robot's end-of-arm tool was equipped with particular technologies, entailing less repair and maintenance. Automotive manufacturers have found the system integration and the implementation of standard autoracking solutions to be extremely cost-effective and adaptable when working with different robot platforms.

Eoat Gripper

You Can Find a EOAT in Capac here:

 



Check the Weather in Capac, Michigan

Cedar Springs Gripper

How to Find a Insert Molding in Cedar Springs ?

Whether the fabricator’s store is large or small, the Ironworker is the backbone. The Ironworker isn’t a single machine; it is five machines united into an engineering wonder. It has much more versatility than most people would imagine. The five working sections that are involved in the make-up of this machine are a punch, a section shear, a bar shear, a plate shear, and a coper-notcher.

A number of the cheaper ironworkers are constructed to employ a fulcrum where the ram shakes back and forth, constructing the punch go into the die at a small angle. This normally leads to the eroding of the punch and die on the front rims. The higher quality machines integrate a ram which moves in a direct vertical line and utilizes modifiable gibs and guidebooks to insure a constant traveling path.

Injection Molding Materials

When you look for a End of Arm Tooling (EOAT)  that develop a Insert Molding in Cedar Springs, looks for experience and not only pricing.

That devotes more life to the tooling, and allows the punch to penetrate the succumb right in the middle in order to capitalize on the machine’s total tonnage.

When looking for a design house that designs a Insert Molding in Cedar Springs  don’t look just in Michigan , other States also have great providers.

Plastic Injection Machine

Scroll Saw Selection - Choosing the Right Saw for Your Needs

?

Sprinklers may get bent or broken by accident. Most of them are made from hard materials that do not get damaged easily but accidents do happen. Broken Arm Spring can be repaired by, pulling the fulcrum pin with a diagonal or side cutting pilers. You should press the pin in the body and it should come out when pulled.

Please go on performing as we suggest, hold the arm in your hand such that the cup part of the spoon facing you and spoon end of arm pointed to your right, now feed end of spring into the hole which is on your right then on through the hole on the left from the back side. Now look end of spring pointing towards you. Let's bend over end near about half with the help pf needle needle node pilers.

The length of spring is normally more than required. Hold arm with spoon end pointing toward you looking down on top of arm. Now cut off the tag end of the spring at the center line of the arm. Now install arm in the body. With the help of hammer drive fulcrum pin into lower hole. Pull arm around as far as it will go, away from nozzle and feed upper end of spring into the hole that is at a distance from the nozzle. Now feed through the other hole so it extends about "1/8" and bend this extended spring end over sharply to clinch. Rain Bird distributors and dealers provide Arm weights for some sprinklers model in order to maintain proper spring tension.

Injection Molding Materials Crypto Briefing

Story after story of top talent in Financial firms and Wall Street pivoting to start their own crypto and blockchain startups. The most recent is J.P. Morgan’s former head of blockchain, Amber Baldet, who has announced a new blockchain start-up called Clovyr.

Or there is this guy, who claims Bitcoin could reach as high as $50,000 by the end of 2018.

Regarding the advent of blockchain there’s a nice video here by Fortune. Amber, who most recently served as the bank’s blockchain program lead at JP Morgna Chase, is co-founding a new startup, Clovyr, that aims to help consumers, developers, and businesses explore the nascent, albeit burgeoning, world of blockchain-based, decentralized technologies.

Baldet hopes she can:

Help people think differently about decentralized application design.
  • Baldet’s post-J.P. Morgan plans have been the topic of speculation since she announced her departure from the bank in April. This is part of a growing trend, the writing is on the wall for Wall Street firms that do not remain agile, and now is the right time to pivot to the blockchain and crypto that are still somewhat nascent and could eventually disrupt financial markets and how financial services work on very fundamental levels.
Shaun Mader | FilmMagic | Getty Images

Amber won’t be the first or the last to leave the comfort of Wall Street, let’s remember where Jeff Bezos got his mathematical and strategic roots.

Baldet unveiled a Clovyr demo at the Consensus conference in Manhattan on Monday afternoon, May 14th, 2018. They are fundraising now as well.

Will Clovyr be the Apple Store for Decentralized Apps?

Baldet co-founded Clovyr with Patrick Nielsen, who led development for J.P. Morgan’s open source blockchain projects.The new company will offer something similar to an app store, but for “decentralized applications” which exist on a blockchain, points out CNBC.

Build it and they will come, we know that the blockchain is coming, even Amazon announced another major partner in its efforts on the cloud. We already knew this but Amazon’s cloud computing arm is now teaming up with startup Kaleido to help simplify blockchain technology for its clients.

Clovyr feels very much like a B2B platform dApp ecosystem in the making:

Clovyr is a decentralized application store that will host a selection of well-vetted applications alongside some in-house developer tooling designed to simplify application development for enterprises.

Seriously though, who would not want to invest in something like this?

Fortune Video

Anticipating the future is not very hard if you are a blockchain enthusiast. She is joined by Nielsen (above), former lead developer of Quorum, a JPMorgan Chase-built blockchain for business, who will serve as the concern’s chief technologist. If JP Morgan Chase is not even able to retain it’s top blockchain people, something is seriously wrong with their R&D model.

Or hang on a second, is this a spin-off play by JP Morgan itself? The report goes on to say: maintaining a “blockchain agnostic” approach to application design, Clovyr will initially provide tooling to build on both public and enterprise versions of ethereum, specifically the Quorum. These Wall Street firms know that they have to appear independent with their innovation startups to gain trust of Millennials. Someone that calls Bitcoin idiotic is probably not on the inside track of trust to the crypto hoard.

What Clovyr reminds me of is essentially a “Shopify of Crypto”, as the cofounders envision the platform serving as a neutral ground, offering a browser-like dashboard for the blockchain-curious, through which Clovyr can provide support and other services to customers according to their needs.

Does the concept make any sense to you?

Injection Molding Cost

You Can Find a EOAT in Cedar Springs here:

 



Check the Weather in Cedar Springs, Michigan